Getting Started with Plumbing Basics When Installing a Bathtub
Getting Started with Plumbing Basics When Installing a Bathtub
Blog Article
Were you trying to locate help and advice concerning A Step-by-Step Guide to Installing a Bathtub?
Setting up a bathtub isn't specifically brain surgery, however it does call for solid plumbing, carpentry, as well as often, tiling abilities. Replacing an old tub with a brand-new one is likewise a reasonably challenging task. If the old bathtub is easily obtainable, the task can relocate rapidly; if you need to open a wall to get rid of the old bathtub and also place the new bath tub, the task is much harder. In either case, the job is within a residence handyman's abilities, although you will certainly require a helper to leave the old bathtub as well as embeded in the new one. Make certain you have qualified yourself for the job and are comfortable attempting it. As opposed to employing a contractor to take over a halfway-completed project, it is much better to think about utilizing one prior to you start. Possibilities are you may need a professional plumber to make tube links.
This write-up will certainly aid you install a new bathtub in your bathroom if you have actually already bought a brand-new tub and do not need to alter the arrangement of your previous water supply pipelines.
Your devices and also product checklist need to consist of the following:
Planning for the Installment
First of all, the sustaining frame provided with the bath must be fitted (if called for) according to the manufacturer's directions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is important to see to it that if the faucet comes with a plastic washing machine, it is fitted between the bath and the taps. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the faucets device to stop pressure on the bath tub.
Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts and olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you utilize every one of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath should now prepare to be fitted in its last placement.
Removing Old Taps
If you require to replace old taps with new ones as a part of your installation, after that the first thing you must do is detach the water. After doing so, activate the taps to drain pipes any type of water continuing to be in the system. The procedure of removing the existing taps can be rather problematic because of the restricted accessibility that is typically the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the taps. Have a fabric all set for the staying water that will certainly come from the pipes. When the supply pipelines have been removed, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single taps from turning throughout this procedure. Once the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any type of old sealing substance.
Prior to going on to fit the new taps, compare the pipe connections on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is required for the new taps to fit.
Installing the Bathtub
Using the two wooden boards under its feet, put the tub in the required placement. The wooden boards are handy in evenly spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 small factors.
The following goal is to ensure that the bath tub is leveled all round. This can be achieved by inspecting the spirit level and adjusting the feet on the bath tub up until the spirit level checks out level.
To install faucets, fit all-time low of the outermost flexible tap connector to the appropriate supply pipeline by making a compression sign up with; after that do the exact same for the various other tap.
Switch on the water supply and also examine all joints as well as new pipework for leakages as well as tighten them if required. Fill up the bath tub and also check the overflow outlet as well as the regular electrical outlet for leaks.
Ultimately, repair the bath paneling as described in the producer's user's manual. Tiling as well as securing around the bathtub should wait till the tub has been made use of at least when as this will certainly settle it into its last position.
Fitting New Touches
If the tails of the new taps are plastic, after that you will require a plastic port to prevent damages to the string. One end of the adapter fits on the plastic tail of the tap and the various other end offers a link to the existent supply pipelines.
If you require to fit a monobloc, after that you will require decreasing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin ensuring that the washing machines are in place in between the faucet as well as the sink. Protect the tap in position with the maker supplied backnut. When the faucet is firmly in position, the supply pipelines can be linked to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with regular tap ports. The former type must be linked to the tap finishes first, tightening just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the area where the bathroom meets the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to split an inflexible seal, causing the water to permeate the wall in between the bathroom as well as the tiling, resulting in problems with moisture and also feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your fixtures and fittings. They are sold in tubes and cartridges, as well as can securing gaps as much as a size of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always fill the bath tub with water before sealing, to allow for the motion experienced when the bathtub remains in use. The sealant can fracture rather early if you do not think about this movement before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also conveniently available on the market. It is a good idea to fit the floor tiles using waterproof or water resistant sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was guided to that article on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround from someone on another site. Sharing is nice. Helping others is fun. Thank you for your time. Please stop by our site back soon.
Affordable? Call now! Report this page